CGI Sliding & Patio Doors Nationwide | TruePane Windows & Doors

CGI Sliding & Patio Doors: The Fort Lauderdale Owner’s Guide

CGI sliding and patio door replacement parts in Fort Lauderdale typically run between $185 and $1,400 installed, depending on whether you need rollers, a lock set, weatherstripping, or a full panel rebuild. We stock common CGI-compatible hardware on our trucks and can usually complete a parts swap in a single visit. Most owners discover the failure the way you probably did: the door starts dragging across the track, the latch stops catching cleanly, or a seal lets the afternoon humidity in around the frame.

Call (754) 310-3589

The salt air here does not negotiate. After fifteen to twenty years of Atlantic exposure, even CGI’s heavier extruded frames start telling you where the weak points are. The good news is that most failures are mechanical, not structural, and the fix is measured in hours, not weeks. Dale Kessler and our crew have been matching CGI hardware to original specs for years, because a part that is close but not correct will wear out the track it rides on.

Which CGI Models This Applies To

CGI’s sliding and patio door lines share a lot of common hardware, but there are compatibility gotchas you need to know before ordering anything. CGI has manufactured several distinct series over the years, including the Estate Collection, the Sentinel line, and various builder-grade impact units sold under different names. The roller assemblies, lock mechanisms, and weatherstripping profiles are not universal across all of them.

The fastest way to identify what you have is to look for the manufacturer label, usually etched or stickered on the head jamb or the edge of the operating panel. If that label is gone (sea air eats adhesive), measure the roller housing width and the track profile. CGI tracks are frequently thicker than the generic hardware-store rollers can accommodate, which is why we see so many “new” rollers that bind within a year. When an OEM part is discontinued or on a six-week backorder, we will tell you plainly and offer a quality aftermarket equivalent that matches the original dimensions, not just the general size. For CGI specifically, we lean OEM on lock sets and keep aftermarket options for rollers and weatherstripping where the engineering is simpler. We also stock parts for PGT, CWS, and ES Windows, but CGI is a line we know cold because so many Fort Lauderdale homes were built or retrofitted with it after Hurricane Andrew.

Signs Your CGI Sliding & Patio Doors Is Failing

• The door grinds or shudders when you slide it. Flat spots on the roller bearings or grit packed into the wheel housing are the usual culprits. Once a roller stops spinning, it turns into a metal sled scraping the track, and that track gets grooved fast.
• The latch does not catch without lifting or forcing the panel. Frames settle, especially here where sandy soil shifts with the water table. The strike plate is out of alignment, or the keeper spring inside the mortise lock has given up. Forcing it only bends the hardware further.
• You feel a draft or see daylight at the bottom or against the interlock. The wool pile or vinyl weatherstripping has compressed or rotted. In a CGI unit, the interlock seal between panels is the first thing salt air destroys, and once it goes, you are air-conditioning the patio.
• The door is visibly harder to move than it was two years ago. Sometimes it is not the rollers, it is the track surface. A scored or pitted track will chew through a new roller set in six months. We measure the track when we diagnose, because replacing rollers on a ruined track is throwing money away.
• Water stains on the interior frame or a damp smell near the threshold. That is the sill flashing or the corner gaskets failing. In a hurricane-rated door, a compromised seal is not just a comfort issue, it is a performance issue, and it will not improve on its own.

Replacement Cost & What’s Included

Here is what Fort Lauderdale homeowners should expect to pay for common CGI sliding and patio door parts work, installed:

What drives the range is the size of the panel, which CGI series you have, and whether the track needs resurfacing or only cleaning. Every quote we write is a line-item price, parts and labor separated, so you see exactly what the hardware costs and what the labor costs. We do not pad parts, and we do not surprise you with a change order once the panel is off. The workmanship is covered by our 90-Day Done Right Promise, and we register manufacturer warranty layers in writing before we leave the driveway.

DIY or Call Us?

You can safely check a few things yourself: clear the track of sand and debris with a dry brush, tighten any screws on the handle that feel loose, and note whether the panel feels heavier on one side. Those observations help us diagnose faster. What you should not attempt is lifting the panel out of the frame. An CGI impact-rated sliding panel can weigh well over two hundred pounds, and if it tips, it will damage the frame, the glass, or you. We have seen a homeowner lose a foot to a panel that came off its track because the anti-lift block was removed back in the original install.

Hardware internals, roller extraction, and lock set replacement are jobs where the wrong removal sequence bends metal that does not bend back. If the door is dragging, grinding, or not latching, call (754) 310-3589 and let us put eyes on it. The diagnosis is free with the estimate, and most repairs are done the same day we show up.

FAQs