Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Before
After
Before
After
Before
AfterTherma-Tru Shingle, Tile & Metal Roofing in Fort Lauderdale: What to Know First
Therma-Tru shingle, tile and metal roofing repair in Fort Lauderdale typically runs between $285 and $1,900 depending on whether we’re replacing a single failed component, re-flashing a penetration, or rebuilding a rotted transition. We’re an independent Therma-Tru service provider, not a factory affiliate, which means we answer to you and your roof rather than a corporate warranty department. Most Therma-Tru repair calls we get are diagnosed and fixed in one visit, usually two to four hours on site. If you own a Therma-Tru roof and something’s leaking, lifting, or showing rust, call (754) 310-3589 and we’ll come look at it.
This page is for Fort Lauderdale homeowners who already have Therma-Tru products overhead and want a straight answer about what’s wrong, what it costs, and whether it’s worth fixing. We’ve worked on enough Therma-Tru shingle, tile and metal roofing in Broward County to know where these systems fail, why they fail here specifically, and what a repair ought to cost without padding the bill. If you’ve been burned by a roofer who disappeared after the first rain, you’re in the right place.
How Therma-Tru Products Fail - and How We Fix Them
Therma-Tru builds good roofing products, but Fort Lauderdale weather is hard on everything. Salt air, afternoon squalls, and UV that bakes a roof to 140 degrees in July create failure patterns we see year after year. Here’s what actually goes wrong:
- Shingle edge curling on the Classic Series line. The asphalt-saturated fiberglass mat on older Classic Series shingles tends to curl at the corners after six or seven years of direct south-facing Fort Lauderdale sun. The sealant strip degrades unevenly, and once a corner lifts, wind-driven rain gets underneath. We don’t just re-seal the lifted corner; we check the entire slope for sealant breakdown and replace any shingle that’s lost its bond. Re-sealing a corner on a shingle that’s already UV-cooked just buys you one more season.
- Tile slippage at the eave on the Terraza clay line. Terraza clay tiles hold up well to salt air, but the copper wire ties used in original installations corrode faster in coastal humidity than anyone expects. When ties snap, tiles start walking downhill and crack against each other. We replace the broken ties with stainless steel, reset the tile course, and verify the underlayment hasn’t been shredded in the process. This one shows up most in Fort Lauderdale neighborhoods east of US-1, where the salt content in the air is highest.
- Standing seam fastener backout on the Metal Ridge series. Therma-Tru’s Metal Ridge standing seam panels use concealed clips, but the fasteners at the eave and ridge transition were often driven too fast at original install, stripping the threads in the decking. Two or three hot summers later, the thermal expansion cycles work those fasteners loose, and you get a panel that rattles in wind and leaks at the seam. We pull the stripped fasteners, install oversized stainless screws, and re-torque the entire run to spec. The fix is simple; the diagnosis is what matters.
- Flashing failure at penetrations across all Therma-Tru shingle lines. This is the most common call we get, and it has nothing to do with Therma-Tru’s manufacturing. The pipe boots and chimney flashing originally installed were builder-grade aluminum, and Fort Lauderdale’s salt air eats aluminum flashing in under a decade. When the flashing fails, water follows the penetration into the decking. We replace with stainless or copper flashing and re-bed everything in polyurethane sealant. The repair is permanent, not a re-caulk job.
- Ridge cap separation on the Vintage Shingle line. Vintage Shingle ridge caps are nailed on, not sealed, and the adhesive strips manufacturers use to bond the cap to the ridge shingle lose grip in high humidity. Fort Lauderdale’s summer humidity is brutal on adhesives. Once a cap lifts, rain drives straight into the ridge line and rots the decking from the top down. We re-set the caps with a mechanical fastener and sealant combination that outlasts the original adhesive strip twice over.
Our Therma-Tru Shingle, Tile & Metal Roofing Process
- 1
The call. You reach a live person at (754) 310-3589, not a voicemail tree. We ask what you’re seeing: water stains, missing granule pile in the gutter, a tile in the yard, a rattle when the wind blows. We schedule a visit at a time that works for you.
- 2
The inspection. A background-checked, uniformed tech walks the roof and the attic if accessible. We look for exactly the failure modes above, photograph everything, and measure twice. We’ll show you photos of what we found before touching anything.
- 3
The decision. We quote OEM Therma-Tru components where they matter (matching tile profiles, shingle color blends) and quality aftermarket fasteners, flashing, and sealant where they outperform the original spec. You see the line items on paper before we start.
- 4
The work. We do the repair in one visit when it’s a contained fix. We re-flash, re-fasten, re-seal, and replace precisely the components that failed. No change orders, no surprise line items.
- 5
The test. We water-test the repair with a controlled hose at the affected area, then walk the roof again to verify nothing else is compromised.
- 6
The guarantee. Every Therma-Tru shingle, tile and metal roofing repair carries TruePane’s 90-Day Done Right Promise. If it isn’t done right, we come back and make it right. No paperwork fights, no arguing.
What Therma-Tru Shingle, Tile & Metal Roofing Costs in Fort Lauderdale
Here’s what we actually charge for common Therma-Tru roofing work in Fort Lauderdale, not what a national franchise estimator says a job “starts at.” These are real ranges from our bids:
- Single shingle replacement (Classic or Vintage lines): $85 to $165, including matching the granule blend as closely as available stock allows.
- Flashing replacement at a single penetration (pipe boot, vent, or stack): $225 to $450, depending on access and decking condition.
- Tile reset at eave with stainless wire tie replacement (Terraza or comparable clay systems): $180 to $520 for up to twelve tiles, plus underlayment patching if needed.
- Standing seam fastener backout repair (Metal Ridge series, per panel run): $300 to $700, including replacing stripped fasteners along the affected run.
- Ridge cap re-set on Vintage Shingle or similar: $285 to $640, depending on linear footage and sealant requirements.
What moves the price: roof pitch and access, decking rot discovered during the repair, and whether we’re matching OEM tile or shingle colors that have been discontinued. Any Fort Lauderdale roofing quote under $200 for a “full flashing replacement” should make you suspicious. Call (754) 310-3589 for a written, line-item estimate on your specific Therma-Tru roof. Estimates are free, and we don’t charge a trip fee to quote within Broward County.
Why Fort Lauderdale Homeowners Call TruePane Windows & Doors for Therma-Tru Work
We’re a second-generation glazier’s company, founded by Dale Kessler in 2008, and we’ve spent the years since building a reputation in Fort Lauderdale for doing what we say we’ll do. When you call TruePane about your Therma-Tru roof, you get a live person on the phone, a uniformed tech who knows the difference between a Vintage Shingle ridge cap and a Classic Series shingle tab, and a written quote before any work starts. Dale measures twice, specs it right, and puts it in writing, because the frame does not forgive shortcuts.
We also work on PGT, CGI, CWS, and ES Windows products, so if your roof repair touches a skylight, a roof-window, or a wall-to-roof intersection tied into glazing, we’re already the company who knows both sides of that transition. That matters more than people think. A roofer who doesn’t understand window flashing is how Fort Lauderdale attics get wet. We stand behind every repair with the 90-Day Done Right Promise and The Keystone Standard: both warranty layers registered in writing before our truck leaves your driveway.
FAQs
We’re an independent service provider, not a Therma-Tru dealer, so we don’t process factory warranty claims directly. What we do is perform repairs that don’t void your existing Therma-Tru warranty, using OEM components where the warranty requires them. We document every repair with photos and line-item parts lists so you have what you need if you file a claim. Call (754) 310-3589 and we’ll tell you honestly whether a factory claim is worth pursuing before we do any work.
Most common Therma-Tru shingle, tile, and metal components are in stock at two Broward County supply houses we buy from weekly, so we can usually source parts same-day or next-day. Discontinued colors and older tile profiles may take three to five business days, and we’ll tell you that before you commit to the repair. The honest answer is that parts availability depends on which Therma-Tru line you have, and we’ll know within a couple hours of looking at your roof.
If your roof is under ten years old and the failure is localized (one flashing point, one tile, one panel run), repair is almost always the right call and costs a fraction of replacement. If you’re seeing multiple failure points across the roof, granule loss on shingles across an entire slope, or decking rot in more than one spot, replacement starts making financial sense. We’ll give you a straight answer either way, not a sales pitch. Call (754) 310-3589 for an assessment.
We match as closely as current production allows. For active Therma-Tru lines, the color match is usually exact or imperceptible once installed. For discontinued shades, we source the closest available blend and tell you honestly what the difference will look like before you pay for it. Tile matches are generally easier than shingle matches because the kiln-fired colors on Terraza and similar lines age more predictably than asphalt granule blends.
No, unless we find hidden decking rot or structural damage that wasn’t visible during the inspection. If that happens, we stop work, show you what we found, and give you a new written number before proceeding. You never get a surprise line item at the end of a TruePane job. That’s the square deal we’ve run on in Fort Lauderdale since 2008.
Get a Straight Answer on Your Therma-Tru Roof
If you have a Therma-Tru shingle, tile or metal roof in Fort Lauderdale that’s leaking, lifting, rattling, or just looking tired, we’ll come look at it and tell you what’s actually wrong. No scare tactics, no unnecessary replacement pitch. Call (754) 310-3589 to schedule your free estimate. A live person answers, every time.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Fort Lauderdale and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.