Mr-Glass Impact Windows Nationwide | TruePane Windows & Doors

Mr-Glass Impact Windows in Fort Lauderdale: What to Know First

We install and service Mr-Glass impact windows throughout Fort Lauderdale, and most jobs are finished in a single visit. As an independent Mr-Glass service provider, TruePane Windows & Doors handles everything from a single failed sash to full-impact retrofits, with free estimates and square pricing before any work begins. If you own a Mr-Glass unit that’s fogged, sagging, or not closing square, call (754) 310-3589 and a live person answers, day or night.

Call (754) 310-3589

This page is written for Fort Lauderdale homeowners who already have Mr-Glass windows, or are considering them, and want straight answers about how they hold up in salt air, what they cost to keep in service, and who in this city actually knows how to work on them.

How Mr-Glass Products Fail - and How We Fix Them

Every window line has its own habits. Mr-Glass is no exception, and in Fort Lauderdale’s humidity and storm cycles, certain failures show up more than the manufacturer brochures discuss. Here’s what we actually see in the field:

• Sash sag on Mr-Glass horizontal rollers. The Mr-Glass 700 Series horizontal roller uses a nylon wheel that wears flat under daily use. Once the wheel flattens, the sash drops a few millimeters and starts scraping the track. Homeowners near the Intracoastal notice it sooner because salt grit accelerates the wear. We shim and re-level the sash, then replace the roller assembly with an OEM or equal-duty aftermarket set depending on age and warranty status.
• Weep-hole blockage on Mr-Glass impact sliders. Fort Lauderdale’s afternoon downpours push pine needles, pollen, and fine sand into the track. When the weep holes in a Mr-Glass impact slider clog, water no longer drains from the track and it pools against the frame. Left alone, it seeps into the drywall below the sill. We clear the weep system, verify it drains with a measured water test, and show the homeowner where to check during rainy season.
• Seal failure on Mr-Glass 300 Series fixed lites. We replace more fogged Mr-Glass 300 Series fixed units than any other line in the brand. The insulating glass unit slowly loses its inert gas fill, and once moisture clouds the space between the panes, no wipe-down fixes it. The solution is an IGU replacement, and on impact-rated units, that means a new lite with the correct laminate layer for the wind zone. We spec that lite to the original design pressure rating, not just the visible dimensions.
• Warped interlock on Mr-Glass casement impact windows. Casement windows live by the interlock, and on Mr-Glass casements the interlock rail bends if the window is forced open against the wind. Fort Lauderdale’s gust fronts can do that before the operator has time to react. A bent interlock means the window never closes flush, and storm-driven rain finds the gap. We straighten or replace the interlock rail and re-square the sash so the seal lands tight across the full frame.
• Deteriorated glazing tape on Mr-Glass storefront-impact hybrid units. On some Mr-Glass commercial-to-residential crossover products, the original glazing tape dries and loses adhesion after six or seven years of UV exposure. The glass stays in place but the seal becomes cosmetic-only, letting water sit against the frame. We remove the old tape, prep the rabbet, and re-glaze with marine-grade tape rated for South Florida UV and moisture. Then we register the repair in writing under our workmanship guarantee.

Dale Kessler grew up in a glass shop in Columbus, Ohio, where his father taught him what a bad seal and a sloppy bedding job look like up close. He brings that same eye to every Mr-Glass window we open, and our techs follow the rule he keeps on the shop whiteboard: if the pane is not true, the job is not done.

Our Mr-Glass Impact Windows Process

We treat a Mr-Glass job the way a second-generation glazier treats any opening: as a structure with a job to do, not a product to swap. Here’s how it goes:

1. 1
   Call and diagnosis. You reach a live person at (754) 310-3589, describe the symptom, and we schedule a visit. Before the tech arrives, we research your home’s wind zone and the Mr-Glass line you have, so the truck carries the right test gear.
2. 2
   The on-site read. Our tech measures each opening twice and checks the surrounding framing. We look at how the window sits in the opening, how the reveal is spaced, and whether water has been finding a way in. This matters because a Mr-Glass unit can fail from an installation mistake as often as from a product fault.
3. 3
   Parts decision, on paper. We quote OEM Mr-Glass parts alongside equal-duty aftermarket options with the prices side by side. Homeowners see exactly what’s going in and why. On impact-rated units, we spec the replacement lite or hardware to the original design pressure, not a close-enough guess.
4. 4
   The repair, done in one visit. Most Mr-Glass impact window repairs are finished same day. Our techs are background-checked and uniformed, and they work in your home the way they’d work in their own mother’s. Drop cloths go down, old parts come out, new hardware goes in square.
5. 5
   The test and the paperwork. Before we pack up, we cycle the window through its full range and check the seal contact. Then we register both manufacturer warranty layers in writing if applicable, and we write up the work under our 90-Day Done Right Promise with the durations stated. No fine print that covers neither.
6. 6
   Cleanup and checklist. We remove the old hardware and glass, vacuum the track, and leave the sill dry. You get a written summary of what we fixed, what we saw, and when to look at it again.

Measure twice, spec it right, and put it in writing - the frame does not forgive shortcuts.

What Mr-Glass Impact Windows Costs in Fort Lauderdale

Pricing stays honest because we quote line items, not mystery bundles. Here’s what Fort Lauderdale homeowners typically see on a Mr-Glass impact window job:

• Single fogged lite replacement (300 Series fixed): $290-$520 depending on size and laminate spec.
• Horizontal roller assembly replacement (700 Series): $175-$340 per sash including adjustment and lube.
• Full casement interlock repair and re-square: $225-$480 per unit.
• Weep system clearing and drain verification: $85-$160 when done as part of a larger repair.
• Complete single-window impact retrofit (mid-size): $1,800-$3,400 depending on opening size, frame condition, and wind-zone requirements. Full-home retrofits range from $14,000 to $40,000 or more, measured opening by opening.

What moves the price: the size of the opening, whether the existing frame is square and dry, the design pressure rating required for your zone, and whether the unit needs OEM Mr-Glass parts or an equal-duty alternative. Seniors and veterans get a permanent 5% discount, and we offer $50 off any repair over $250. Call (754) 310-3589 for a free estimate and a written line-item quote.

Why Fort Lauderdale Homeowners Call TruePane Windows & Doors for Mr-Glass Work

We’ve been serving Fort Lauderdale and the surrounding communities long enough that some of our original customers’ grandchildren are now calling us for their first home. That’s the point. We’re not a franchise playbook; we’re a local operation that trains apprentices into journeymen and plans to be in town in thirty years. For Mr-Glass owners in Fort Lauderdale, that means a crew that knows the brand’s habits, keeps the right parts on the truck, and never rushes a seal job before a storm. We quote every job honestly, do the work in one visit when possible, and back it with 90 days. No arguing, no paperwork fights.

And when the right fix isn’t a Mr-Glass part, we’re authorized installers for more than a dozen other manufacturer lines, including PGT, CGI, CWS, and ES Windows. We’ll tell you straight when a replacement makes more sense than another repair, and we’ll put both options on paper side by side. A square deal, in writing.

FAQs