Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Before
After
Before
After
Before
AfterCWS Roof Replacement & Installation in Fort Lauderdale: What to Know First
We handle CWS roof replacement and installation across Fort Lauderdale as an independent CWS service provider, with most jobs quoted on paper and scheduled within one to two weeks once parts land. Pricing runs higher than a handyman’s guess because we spec the right glass, the right frame, and the right flashing before we touch the opening, but you'll never see a surprise line item on the bill. This page is for CWS owners who want the work done once. Call (754) 310-3589 for a free estimate and a straight answer about what your roof actually needs.
How CWS Products Fail - and How We Fix Them
Every brand has its habits. CWS units do certain things in Fort Lauderdale that we see on other jobs less often. Here’s what we find when we walk a CWS roof:
- CWS Series 8500 / Series 7500 corner seal breakdown. These extruded-aluminum outswing units carry a lot of glass weight, and after ten or twelve years of Fort Lauderdale sun the corner gaskets shrink and harden. You’ll see water staining on the interior drywall beneath the mullion first, not a drip from the glass. We pop the sash, inspect the corner keys, and replace the seal with an ozone-rated compound that holds up longer than what the factory used in earlier runs.
- CWS Series 9500 multi-slide track wear on beachside properties. Salt air is rough on roller hardware, and the 9500 multi-slide is a tank until the rollers go. Fort Lauderdale homeowners within a mile of the water often report the door "getting heavy." That’s usually a roller with a flattened bearing. We replace the roller assembly with aftermarket stainless units that are half the price of the OEM set and last as long in this climate.
- CWS casement operator failure on Model 8100. The worm gear inside the operator strip is a known weak point. When it fails, the sash won’t fully seat, and the unit starts to leak at the bottom corner. Rather than replacing the whole sash, we swap the operator and re-lock the sash against the frame. Half the time the original glass is still perfectly fine.
- Roof-to-frame flashing mismatch on retrofits. We see this on CWS roof installs done out of square by other crews. Fort Lauderdale’s afternoon downpours find a bad flashing joint in months, not years. We read the rough opening and the existing subfloor before we quote. If the frame is out of true by more than an eighth of an inch, we call it. Dale Kessler grew up measuring rough openings in his father’s glass shop, and he still runs a tape on every roof job.
- Weep hole blockage in CWS fixed units. CWS fixed roof units rely on weep slots at the bottom track. Fort Lauderdale’s oak pollen and airborne salt combine to clog those slots faster than most people expect. Standing water in the track is the tell. We clear the weeps and add micro mesh strips so the problem doesn’t recur after the next storm.
Our CWS Roof Replacement & Installation Process
Every CWS roof job follows the same sequence. No shortcuts, no second guessing:
- 1
Walk and measure. We inspect the existing CWS unit, check the frame for square, and read the flashing. Measurements go on paper, not in a head.
- 2
Parts decision. We lay out OEM versus quality aftermarket options side by side with prices. If your CWS warranty is still live, we protect it. If it’s expired, we spec what actually serves the house, not what pads the invoice.
- 3
Written quote. Fixed price, no change orders. You see the number before we order anything.
- 4
Removal and prep. The old CWS unit comes out carefully. We repair or reinforce the rough opening before the new unit goes in.
- 5
Install and flash. New unit set, squared, and sealed. Flashing done to handle a Fort Lauderdale summer storm, not a light rain.
- 6
Test and walk-through. We run the unit through its full range, check the weep drainage, and show you what we did. Then the 90-Day Done Right Promise applies, in writing.
What CWS Roof Replacement & Installation Costs in Fort Lauderdale
Here are honest ranges for the CWS work we do most often in Fort Lauderdale:
| CWS Job | Typical Fort Lauderdale Range |
|---|---|
| Fixed unit seal replacement (per unit) | $275 - $450 |
| Casement operator replacement | $180 - $320 |
| Multi-slide roller replacement (per panel) | $195 - $375 |
| Full CWS roof unit replacement, standard size | $2,400 - $5,800 |
| Flashing repair on an existing CWS roof install | $350 - $700 |
The spread comes down to glass package, frame condition, access difficulty, and whether we’re matching an existing CWS line or starting fresh. Call (754) 310-3589 with your CWS model number visible and we’ll narrow that range to a fixed number. The estimate is free.
Why Fort Lauderdale Homeowners Call TruePane Windows & Doors for CWS Work
We’ve been serving Fort Lauderdale and the surrounding communities for years, and we act like a company that plans to be here in thirty more. Every CWS job gets our 90-Day Done Right Promise in writing: if it’s not done right, we make it right, no paperwork fights and no arguing. Our technicians are background-checked, uniformed, and they measure twice before they quote. If a CWS repair turns out to be a full replacement, we’ll quote PGT, CGI, ES Windows, and ECO Window Systems side by side so you can see exactly what your money buys. A live person answers the phone 24/7 at (754) 310-3589.
FAQs
Yes, in most cases we can match the CWS frame profile and glass package, though an exact color match on discontinued lines sometimes requires repainting the new frame. We’ll tell you if a match is not possible before you spend anything. Call (754) 310-3589 and we’ll check your model number.
If your CWS unit is still under warranty, we work to the manufacturer’s repair specs and document every step so the warranty stays intact. If it’s expired, we recommend the parts that actually hold up in Fort Lauderdale’s sun and salt. We’ll lay out both paths in writing.
Most single-unit CWS replacements are done in one day once the parts are in hand, usually one to two weeks after you sign the quote. A complicated flashing job or a multi-unit replacement can push into two days. We’ll give you a finish date in writing before we start.
If the frame is square and the hardware failed, repair is almost always the cheaper call. If the frame itself has corrosion or the glass seal is blown, replacement wins. We’ll show you the numbers on both paths and let you decide. Call (754) 310-3589 for an exact quote.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Fort Lauderdale and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.